| LAND MOBILE RADIO PRODUCTS ONLY ~~~ PRODUCTS SHOWN ON THIS WEB PAGE ONLY ~~~ ~ COMET ~ MALDOL ~ DAIWA ~ ~ ANTENNAS ~ MOUNTS ~ SWR METERS ~ BRYAN WADSWORTH CELL PHONE (815) 790-4494 We can sign you up as a new "Land Mobile Radio Dealer" with the products below Call or E-Mail us for the details! HAM RADIO PRODUCTS You must purchase these from the "Ham Radio Distributors" like AES and HRO etc. We can only sell the Land Mobile Radio Products that are listed on this web page. ~ LAND MOBILE RADIO PRODUCTS ~  All the products shown below are available with a $100 minimum order at 16.625% off current list price from our Master Distributor if you are an End User. -- BEST PRICING ON THE INTERNET - We can also set you up as a New LMR Dealer if you have a FEIN and a Credit Card and you will be authorized with a terrific discount off list pricing. | | C-150BX-H | 148-175MHz (tunable) fixed station antenna
1.5:1 or less SWR: 4MHz after tuning
Gain: 3.4dBi
Max power: 100 watts
Length: 50.5 inches max
Weight: 2 lb 2oz
Connector: SO-239
Construction: Telescoping Aluminum pipe
Max wind speed: 112MPH |
| | | |
|
| | C-150BX-L | 118-145MHz (tunable) fixed station antenna
1.5:1 or less SWR: 4MHz after tuning
Gain: 3.4dBi
Max power: 100 watts
Length: 67 inches max
Weight: 2 lb 6oz
Connector: SO-239
Construction: Telescoping Aluminum pipe
Max wind speed: 112MPH |
| | | |
|
| | CA-F22GF | 136-175MHz (tunable) fixed station antenna
1.5:1 or less SWR: 4MHz after tuning
Gain: 5.5dBi
Max power: 150 watts
Length: 8 ft 10 inches
Weight: 2lbs 8 ozs
Connector: SO-239 (CA-F22GFN N-female connector)
Construction: Two-piece black fiberglass
Max wind speed: 112MPH |
| | | |
|
| | CA-SUPER22 | 220MHz Fixed Station Antenna
1.5:1 or less SWR: 220-225Mhz
Gain: 6.6dBi
Max power: 150 watts
Length: 8 ft
Weight: 2 lb 2oz
Connector: SO-239
Construction: One piece black fiberglass
Max wind speed: 112MPH |
|
|
| | CA-712EFC | UHF Fixed station antenna
1.5:1 or less SWR: 460-470MHz
Gain: 9dBi
Max power: 200 watts
Length: 10 ft 5 inches
Weight: 2 lb 13oz
Connector: N-female
Construction: Two piece white fiberglass
Max wind speed: 112MPH |
| | | |
|
| | CA-F72GF | 440-512MHz (tunable) fixed station antenna
1.5:1 or less SWR: 10MHz after tuning
Gain: 5.5dBi
Max power: 150 watts
Length: 42 inches
Weight: 2 lb 14oz
Connector: N-female
Construction: One-piece white fiberglass
Max wind speed: 135MPH |
|
|
| | GP-6NC | VHF/UHF Dual Band Antenna
1.5:1 or less SWR: 153-157/460-470MHz
Gain: 6.5/9.0dBi
Max power: 200 watts
Length: 10 ft 2 inches
Weight: 3 lb 8 oz
Connector: N-female
Construction: Two piece white fiberglass
Max wind speed: 112MPH |
| | | |
|
| | GP-9NC | VHF/UHF Dual Band Antenna
1.5:1 or less SWR: 153-157/460-470MHz
Gain: 8.5/11.9dBi
Max power: 200 watts
Length: 16ft 6inches
Weight: 3 lb 8 oz
Connector: N-female
Construction: Three piece white fiberglass
Max wind speed: 92MPH |
| | | |
|
| | GP-9NCA | VHF/UHF Dual Band Antenna
1.5:1 or less SWR: 150-154/460-470MHz
Gain: 8.5/11.9dBi
Max power: 200 watts
Length: 16ft 6inches
Weight: 3 lb 8 oz
Connector: N-female
Construction: Three piece white fiberglass
Max wind speed: 92MPH |
|
|
| | KP-20 | 900MHz Access Point Antenna
1.5:1 or less SWR: 900-930MHz
Gain: 9.2dBi
Max power: 50 watts
Length: 8 ft
Weight: 2 lb 4oz
Connector: N-female
Construction: One-piece white fiberglass
Max wind speed: 100MPH |
|
|
| | CLP-5130-1N | Wideband log periodic receive/transmit antenna
2:1 or less SWR: 50-1300MHz
Elements: 21
Polarization: Horizontal
Gain: 10-12dBi
F/B ratio: 15dB
Half power point:
70-60 degree
Max power:
500 watts
Boom length:
6ft 8 inches
Max element length:
9 ft 10 inches
Weight: 11 lbs
Connector:
N-connector
Construction:
Aluminum
Max wind speed:
90MPH |
| | | |
|
| | CLP-5130-2N | Wideband log periodic receive/transmit antenna
2:1 or less SWR:
105-1300MHz
Elements: 17
Polarization:
Horizontal
Gain: 11-13dBi
F/B ratio: 15dB
Half power point:
70-60 degree
Max power:
500 watts
Boom length:
6ft 8 inches
Max element length:
4 ft 4 inches
Weight: 11 lbs
Connector:
N-connector
Construction:
Aluminum
Max wind speed:
90MPH |
|
|
| | CA-2x4SR | BROADBAND VHF/UHF Dual Band Antenna CA-2x4SR: Designed to assist Search & Rescue Volunteers and Professionals
2:1 or less SWR: 140-160/435-465MHz
Gain: 3.8/6.2dBi
Max Power: 150 watts
Length: 40 inches
Connector: PL-259
Fold-over hinge included The CA-2x4SR is a broad-band antenna designed for those needing voice communications on both the ham radio and land mobile frequency ranges. When the amateur radio community is working together with local search and rescue and other public service agencies, the CA-2x4SR antenna allows TX and RX capability in both bands! The coverage area and gain provided by the CA-2x4SR is remarkable. Whether used on VHF or UHF or both, it is an asset to the communications needs of amateurs and land mobile users simultaneously. |
| | | |
|
| | FC-54NMO | VHF/UHF Dual Band Antenna
1.5:1 or less
SWR:
153-157/460-470MHz
Gain: 2.15/5.0dBi
Max Power: 50 watts
Length: 36 inches
Connector: NMO
Fold-over hinge included |
|
|
| | R-2000 | 900 MHz Mobile antenna
1.5:1 or less SWR: 900-930MHz
Gain: 5.1dBi
Max Power: 30 watts
Length: 19.25 inches
Connector: N-male |
|
|
| | CM-5M | Standard 4.5” magnet SO-239 connector on magnet, coax terminates in a PL-259 connector 13' of RG-58A/U coax Rubber boot over the magnet to protect vehicle paint Weather cap provided to cover the SO-239 connector when the antenna is removed |
| | | |
|
| | CP-5M | Universal adjustable lip mount, 16’ 6” deluxe cable assembly with SO-239/PL-259 connectors. Quality appearance and low loss coax cable assembly. Installs easily in only minutes to virtually any lip on a vehicle. Trunk lid, truck rear doors, SUV and van rear doors, hood lip, etc… Does not damage expensive and/or leased vehicles.
Footprint: 3.4" x 1.25"
Mount adjusts in 4 planes. The first 18 inches of coax is mini RG-174A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with 24k gold plated SO-239 & PL-259 connectors. The PL-259 disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place.
Max Power: HF: 100W VHF: 75W UHF: 50W |
| | | |
|
| | CP-5NMO | Universal adjustable lip mount, 16’ 6” deluxe cable assembly with NMO/PL-259 connectors. Quality appearance and low loss coax cable assembly. Installs easily in only minutes to virtually any lip on a vehicle: Trunk lids, truck rear doors, SUV and van rear doors, hood lip, etc… Does not damage expensive and/or leased vehicles.
Footprint: 3.4" x 1.25"
Mount adjusts in 4 planes. The first 18 inches of coax is mini RG-174A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with NMO & PL-259 connectors. The PL-259 connector disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place.
Max Power: HF: 100W VHF: 75W UHF: 50W |
| | | |
|
| | CT-5M | Standard trunk lip mount with SO-239/PL-259 connectors. Adjusts up to 17 degrees to compensate for trunk angle. Included
16’ 6” of RG-58A/U. |
| | | |
|
| | GR-5N | Designed for use with 900-2500MHz mobile antennas that use N-male connectors.
Deluxe trunk lip mount, 16’ 6” cable length with N-female/N-male connectors. Adjusts up to 17 degrees to compensate for trunk angle. Quality appearance and low loss coax cable assembly installs easily in minutes.
The first 18 inches of coax is mini RG-188A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with 24k gold plated N connectors. The N-male connector disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place. |
| | | |
|
| | GRB-5M | Deluxe trunk lip mount, 16’ 6” cable length with SO-239/PL-259 connectors. Adjusts up to 17 degrees to compensate for trunk angle. Quality appearance and low loss coax cable assembly installs easily in minutes. Footprint: 4.25" x 1.9"
The first 18 inches of coax is mini RG-188A/U type allowing easy entry through the weather seal into the vehicle without causing wind noise, water leaks or coax damage. The coax balance is low loss with 24k gold plated SO-239 & PL-259 connectors. The PL-259 connector disassembles for easier routing or to shorten the coax length. Soft rubber pad protects the vehicle paint, 4 large set screws hold the mount firmly in place. |
|
|
| | EM-B80 | Light-Duty, 2 adjustment planes, up to 40” antenna 1.1" x .75 inch footprint allows the EM-B80 to be mounted in a very limited space. Fits where other mounts won't! |
| | | |
|
| | MK-30H | 12VDC motorized mount for trunks/hatch-backs, rear van doors etc. Heavy Duty motor provides convenient lowering/raising of a mobile antenna. Approximately 17 feet of wire allows the up/down switch to be located within the drivers reach. Recommended for antennas up to 70” and weighing 1lb. 3oz. or less. Rubber coated base avoids scratches. Coax cable not included. |
| | | |
|
| | RS-520 | Light duty, 3 adjustment planes, up to 45” antenna |
| | | |
|
| | RS-660U | Roof-Rack Mount Adjusts to attach to larger roof racks, up to 2.5 inch width Recommended for antennas up to 60 inches 5/8" hole accepts SO-239 connectors (Cable assy 3D4M, CK-3M5 etc) or N-female connectors (5D4N, CK-5N etc) When using an antenna with and NMO connector, install the SO-239 cable assy then adapt to an NMO connector with the AD-25M |
| | | |
|
| | RS-720/RS-720NMO | Med-duty lip mount, 3 adjustment planes, holds up to 60” tall antenna. The RS-720NMO has a 3/4” hole to accept an NMO mount. Soft rubber gasket protects the vehicle paint. Attaches to any lip edge on the vehicle with set screws on the underneath side. NO NEED to drill holes. Fits over any edge no more than 1/4" thick, and adjusts to vertical from any angle. Trunk lid/Van door/SUV rear door/Rear truck door/Hood/etc... Footprint: 2.1" x 1.15" |
| | | |
|
| | RS-730 | Heavy-duty 3 adjustment planes, up to 70” antenna |
|
|
| | 3D4M | Standard mobile lip mount cable assembly Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads.
13 feet of low loss coax, .25" outside diameter Gold-plated UHF (PL-259/SO-239) connectors The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector. To shorten the over-all length of the coax: Remove the barrel as above and de-solder the center pin of the PL-259 The connector body then screws apart and the cable can be cut to the desired length. Re-assemble the connector. |
| | | |
|
| | 3D4N | Standard Cable Assembly with N-Connectors. Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads. 13 feet low loss coax, .25" diameter Recommended for use to 1300MHz. Gold-plated N-type connectors The N-male connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the N connector. To shorten the over-all length of the coax: Remove the barrel as above and de-solder the center pin of the N connector The connector body then screws apart and the cable can be cut to the desired length. Re-assemble the connector. |
| | | |
|
| | 3D5M | Standard mobile lip mount cable assembly Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads.
13 feet of low loss coax, .25" diameter Gold-plated UHF (PL-259/SO-239) connectors The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector. To shorten the over-all length of the coax: Remove the barrel as above and de-solder the center pin of the PL-259 The connector body then screws apart and the cable can be cut to the desired length. Re-assemble the connector. |
| | | |
|
| | 5D4N | Low loss mobile mount coax cable assembly Approximate loss: 2dB at 2400MHz 13' very low loss coax cable assy recommended for use up to 2500MHz Coax cable outside diameter: 5/16" Gold plated N-connectors Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads. The N-male connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the N connector. To shorten the over-all length of the coax and avoid excessive cable loss- Remove the barrel as above and de-solder the center pin of the N connector The connector body then screws apart and the cable can be cut to the desired length. Re-assemble the connector. |
| | | |
|
| | CK-3M | Deluxe mobile lip mount cable assembly
Coax length: 9' 9" total
The first 12" of coax is mini RG-174A/U type allowing easy entry into the vehicle through the weather seal without causing wind noise, water leaks or impedance mismatch due to the coax being crimped or damaged. The balance of the coax is low loss, .25inch outside diameter. Gold-plated UHF (PL-259/SO-239) connectors The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector. To shorten the over-all length of the coax: Remove the barrel as above and de-solder the center pin of the PL-259 The connector body then screws apart and the cable can be cut to the desired length. Re-assemble the connector. Max Power: HF: 100W VHF: 75W UHF: 50W
|
| | | |
|
| | CK-3M5 | Deluxe mobile lip mount cable assembly
Coax length: 16' 9" total
The first 12" of coax is mini RG-174A/U type allowing easy entry into the vehicle through the weather seal without causing wind noise, water leaks or impedance mismatch due to the coax being crimped or damaged.The balance of the coax is low loss, .25 inch outside diameter. Gold-plated UHF (PL-259/SO-239) connectors The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector. To shorten the over-all length of the coax: Remove the barrel as above and de-solder the center pin of the PL-259 The connector body then screws apart and the cable can be cut to the desired length. Re-assemble the connector. Max Power: HF: 100W VHF: 75W UHF: 50W |
| | | |
|
| | CR-5M | Standard Cable Assembly
16 feet 9 inches of RG-58/U coax with UHF
(PL-259/SO-239) connectors |
|
|
Q. Whats the difference between NMO and the PL-259 type mounts?
A. If you decide to drill a hole in your car, the NMO (New MOtorola) mount was designed specifically for hole installations. They can be installed from the top and are water proof. So if you want to drill a hole, you should use an antenna with an NMO connector. If you DO NOT want to drill a hole in your vehicle, there are many more external mounts available to choose from made for PL-259 connector antennas.
Q. Should I drill a hole in my roof/trunk or use a lip mount?
A.In the past, most people preferred drilling a hole in the center of the roof or trunk to provide the best ground plane. This made a lot of sense when the repeater systems were poor and most antennas were single band and needed the ground plane. Current antenna design produces antennas that are ground independent. The sensitivity, coverage area and height of most modern repeater systems is outstanding. The antenna no longer needs to be in the middle of a ground plane for excellent coverage.
The benefit of drilling a hole and mounting your antenna in the middle of the roof or trunk is minimal.
Hole Mounting: - Difficult to reach the antenna to remove it or use the fold-over hinge
Water leaks and rust problems are common. - Improved performance
Lip Mount Benefits: - Lip mount installation is quick, easy and no damage to the car
- The antenna is easily reached for removal or to use the fold-over hinge
- Deluxe coax cable easily enters through the weather seal without causing any wind noise, water leaks or coax damage.
- Mount can be removed and re-used on a different vehicle
- Slightly distorted radiation pattern
Because most people look to Comet and Maldol for no holes to drill mounting options, their antennas are tuned for best performance on a lip mount.
Q. I have a truck, where can I mount an antenna?
A. If your truck has a third door or rear doors, the best location for a lip mount is the side of the drivers side rear door near the top. The antenna is above the roof line, no holes to drill and mounting takes only a few minutes.
Q. What mount should I use for a plastic/composite car?
A. Most of the Comet and Maldol antennas we distribute are ground independent and can be mounted to new plastic/composite cars with the standard lip mounts. The exception is any antenna that has an electrical length of 1/4 wave. A 1/4 wave antenna is only half an antenna, the other half is the ground plane. So, a 1/4 wave has to be grounded to work well and have good SWR.
Q. I have a SUV/VAN that doesnt have a trunk, where can I mount an antenna?
A. We receive many calls from people worried that they can't mount an antenna because they dont have a trunk. If you have an SUV or van with a back door, you have the best possible mounting location and you dont even know it. The rear door, whether hatchback style or cargo doors, is the best place for a lip mount. Simply lift or open the drivers side door, slip the preferred mount over the edge near the top of the door and tighten the set screws that hold it to the door. Rotate all the pieces until the mount is vertical, add a coax cable if not included and its mounted. The antenna is above the roof line for the best pattern, its easy to reach if you need to take it off for a car wash or fold it over to get in a garage, no holes are needed and mounting takes only a few minutes.
Q. What mount should I use?
A. Choose the mount that is most appropriate for the antenna you want to use. They all attach the same way. Set screws hold them to the edge, a piece of soft rubber protects the painted surface. The only decision is the size of the antenna should match the mount size. Keep in mind that you may want to get a bigger VHF/UHF or heavier HF antenna some time in the future, so choose the mount size keeping that in mind. We don't have the ability to test all our mounts on every vehicle made, so we can't answer questions related to specific vehicles and model years. However, all of our mounts will attach to virtually any lip on any vehicle provided the thickness of the lip is 1/4 inch or less. Some newer vehicles are using composite materials for some parts. The composite has to be thicker than steel to have the same strength, so it is sometimes more than 1/4" thick. Check the thickness where you want to mount it.
Q. Can I buy parts if I break my antenna?
A. We keep many parts on hand for most but not all antennas. If an antenna has been discontinued, no parts will be available.
Q. Did Comet buy Daiwa and Maldol?
A. No, all three are separate companies in Japan. NCG is the US distributor for all three.
Q. Whats the difference between Comet and Diamond, are they the same company?
A. Comet and Diamond make similar products just as Ford and GM do. Sometimes the same sub-contractors will make parts for both, so the parts will look similar. They both pay attention to quality, innovation and focus on making the best product they can. We feel Comets engineers and quality control are second to none and are proud to the their US distributor. We can sign you up as a new "Land Mobile Radio Dealer" with all the products on this page Call or E-Mail us for the details! BRYAN WADSWORTH CELL PHONE (815) 790-4494 HAM RADIO PRODUCTS You must purchase these from the "Ham Radio Distributors" like AES and HRO etc. We can only sell the Land Mobile Radio Products that are listed on this web page. ~ LAND MOBILE RADIO PRODUCTS ~ All the products shown on this page are available with a $100 minimum order at 16.625% off current list price from our Master Distributor if you are an End User. -- BEST PRICING ON THE INTERNET - We can also set you up as a New LMR Dealer if you have a FEIN and a Credit Card and you will be authorized with a terrific discount off list pricing. | | HT-55 | VHF/UHF Handheld Antenna
2:1 or less SWR: 153-157/460-470MHz
Wide range receive: 118-960MHz
Max Power: 5 watts
Length: 8.75 inches
Connector: SMA-male |
| | | |
|
| | MH-255 | VHF/UHF Handheld Antenna
2:1 or less SWR: 153-157/460-470MHz
Wide range receive: 118-960MHz
Max Power: 5 watts
Length: 3 inches
Connector: SMA-male |
|
|
SPLITTERS & COMBINERS  | | Duplexers | Duplexer/Splitter/Combiner Comet calls these "duplexers", but they are also referred to as combiners or splitters. They are basically band-pass filters, simultaneously passing RF in both directions through the common connector while the band-pass filters provide a high degree of isolation between ports. * TX and RX from two radios at the same time into a dual-band antenna
* Combine a dual-band radio with separate outputs into a dual-band antenna
* Separate a single connector duplexed radio into separate antenna systems
* Allow a single coax run into two antennas at the top of the tower, and two radios at the bottom by using a duplexer at both ends of the coax run, avoiding cost and weight. Choose from versions with a variety of band-pass frequency ranges, coax leads or no leads, and connector combinations |
| | | |
|
| | CF-142 | Band Pass Ins Loss Max Power 1.3-150MHz 0.2dB 600W PEP
200-480MHz 0.3dB 400W PEP Isolation: 40dB minimum
CONNECTORS:
Common SO-239
Low Pass: PL-259 High Pass: PL-259 |
| | | |
|
| | CF-360A | HF/6M-440MHz Duplexer
Band Pass
1.3-30MHz
49-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Output:
SO-239
Low In:
PL-259
High In:
PL-259 |
| | | |
|
| | CF-360B | HF/6M-440MHz Duplexer
BandPass
1.3-30MHz
49-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Common:
PL-259
Low In:
SO-239
High In:
SO-239 |
| | | |
|
| | CF-4160K, 4160I, 4160J, 4160N | BandPass Ins Loss Max Power
1.3-170MHz .1dB 800W PEP Isolation: 60dB mimimum
Connectors:
CF-4160K
Common: SO-239
Low Pass:PL-259
High Pass: PL-259 CF-4160ICommon: SO-239 Low Pass:PL-259High Pass: N-Male
CF-4160J
UHF-Female connectors makes it easy to use your own jumpers between your radio and the duplexer.
Common: SO-239
Low Pass: SO-239
High Pass: SO-239 CF-4160N (NEW) N-Female connectors at all ports for those who want to use all low loss N-type connectors Common: N-Female Low Pass: N-Female High Pass: N-Female |
| | | |
|
| | CF-416A, 416B, 416C | Duplexer/Splitter/combiner Band Pass:
Low Pass: 1.3-170MHz
High Pass: 350-540MHz
Ins. Loss:
0.15dB 800w
0.25dB 500w
Max Power
PEP 800W
PEP 500W
Isolation: 60dB minumum
CONNECTORS:
CF-416A
Common: SO-239
Low pass: PL-259
High pass: PL-259
CF-416B
Common: SO-239
Low Pass: PL-259
High Pass: N-Male
CF-416C
Common: N-Female
Low Pass: PL-259
High Pass: N-Male |
| | | |
|
| | CF-416W | Broad Range Duplexer
BandPass Ins Loss Max Power 1.3-250MHz .2dB 400W PEP
400-1400MHz .25-.3dB 200W PEP
Isolation: 30dB
CONNECTORS:
Common: N-Female
Low Pass: PL-259
High Pass: N-Male
|
| | | |
|
| | CF-530 | HF/6M/2M-70cm Duplexer
For the IC-706/MKII/G FT-100
BandPass
1.3-90MHz
125-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Output:
SO-239
Low In:
PL-259
High In:
PL-259 |
| | | |
|
| | CF-530C | HF/6M/2M – 70cm Duplexer
for the FT-8900
BandPass
1.3-90MHz
125-470MHz
Ins. Loss
0.2dB
0.2dB
Max Power
600w PEP
600w PEP
Isolation:
More than 45dB
CONNECTORS:
Output:
PL-259
Low In:
SO-239
High In:
SO-239 |
| | | |
|
| | CF-706A | HF-6M/2M-440MHz duplexer for the IC-706/MKII/G, FT-100, etc.. To match the RX freq rangeof the IC-706MKII/G the CF-706A was engineered to pass the commercial FM band of 88-108MHz.
Band Pass Ins. Loss Max Power
1.3-57MHz 0.4dB 350w PEP
75-550MHz 0.4dB 350w PEP
Isolation: 40dB minimum
CONNECTORS:
Common: SO-239
Low pass: PL-259 High Pass: PL-259 |
|
|
| | CS-201 | Frequency Range (up to): 600MHz
Power Rating:
2.5 kW PEP
1 kW CW
VSWR: below 0.12
Insertion Loss: less than 0.2 dB
Isolation: 60 dB 600 MHz
Connector: SO 239
Output Port: 2 |
| | | |
|
| | CS-201GII | Frequency Range (up to):2 GHz
Power Rating:
1.5 kW CW (up to 30 MHz)
250 W CW (up to 1 GHz)
150 W CW (up to 2 GHz)
VSWR: below 1:1.3 at 1.3 GHz
Insertion Loss: less than 1.2 dB at 1.2 GHz
Isolation: 50 dB 1 GHz
Connector: Gold Plated N-Type
Output Port: 2 |
|
|
| | CN-101 | Frequency: 1.8-150MHz
Power Range Forward: 15/150/1.5kW
Power Rating:
1.5kW (1.8-60MHz)
1kW (144MHz)
Accuracy: +/- 10% (at full scale)
SWR Detection Sensitivity: 4 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239
Dimensions & Weight: 5” x 3” x 4” / 1lb. 8ozs. |
| | | |
|
| | CN-103M/CN-103N | Frequency: 140-525MHz
Power Range Forward: 20/200W
Accuracy: +/- 10% (at full scale)
SWR Detection Sensitivity: 4 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239/N-Type
Dimensions & Weight: 5” x 3” x 4” / 1lb. 8ozs. |
| | | |
|
| | CN-801HP | Professional Series SWR/Power Bench Meter Cross needle design displays forward power, reflected power and SWR simultaneously. NO Calibration required Frequency: 1.8-200MHz
Power Range Forward: 20/200/2kW
Tolerance: +/- 10% (at full scale)
SWR Detection Sensitivity: 5 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239
Dimensions & Weight: 6.25” x 4.3” x 4.8” / 2lbs. 3ozs. LED Lighted with on/off switch |
| | | |
|
| | CN-801SII | Professional Series SWR/Power Bench Meter Cross needle design displays forward power, reflected power and SWR simultaneously. NO Calibration required Frequency: 900-2500MHz
Power Range: 200mW/2/20W
Accuracy: +/- 10% (at full scale)
SWR Detection Sensitivity: 0.5 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: N-Type
Dimensions & Weight: 6.25” x 4.3” x 4.8” / 2lbs. 3ozs. LED Lighted with on/off switch |
| | | |
|
| | CN-801V | Professional Series SWR/Power Bench Meter Cross needle design displays forward power, reflected power and SWR simultaneously. NO Calibration required Frequency: 140-525MHz
Power Range Forward: 20/200W
Accuracy: +/- 10% (at full scale)
SWR Detection Sensitivity: 5 W min
Input/Output Impedence: 50 OHM
Input/Output Connectors: SO-239
Dimensions & Weight: 6.25” x 4.3” x 4.8” / 2lbs. 3ozs. LED Lighted with on/off switch |
| |
|
We can sign you up as a new "Land Mobile Radio Dealer" with all the products on this page Call or E-Mail us for the details! BRYAN WADSWORTH CELL PHONE (815) 790-4494 HAM RADIO PRODUCTS You must purchase these from the "Ham Radio Distributors like AES and HRO etc. We can only sell the Land Mobile Radio Products that are listed on this web page. ~ LAND MOBILE RADIO PRODUCTS ~ All the products shown on this page are available with a $100 minimum order at 16.625% off current list price from our Master Distributor if you are an End User. -- BEST PRICING ON THE INTERNET -We can also set you up as a New LMR Dealer if you have a FEIN and a Credit Card and you will be authorized with a terrific discount off list pricing. | |